M12 FUEL™ 3/8" Stubby Impact Wrench Kit

The new M12 FUELMC 3/8-inch Stubby Impact Wrench delivers the most power, is lighter, more compact, and offers 50% faster application speeds. The POWERSTATEMC brushless motor delivers 0-3000 RPM with up to 550 ft-lbs of nut-busting torque, allowing removal of the most corroded and stubborn applications. This solution is both powerful and compact, with the bare tool weighing only 2.2 lbs. Users will experience less fatigue throughout their work week. The stubby impact wrench allows them to access tight spaces and areas where larger impact wrenches cannot fit without the use of additional accessories or component disassembly to reach the desired fastener. It features triple LED work lights to illuminate your work area without the frustration of shadows. The 4-mode DRIVE CONTROLMC offers greater precision and customization of desired power. Its AUTO SHUT-OFFMC control applies no more than 15 ft-lbs of torque during hand-tightening applications, preventing overtightening in forward mode. In reverse, the bolt removal mode slows down the RPM once the bolt is loosened, to prevent bolts from flying around your work area. Mode changes are done with one hand. By putting the locking device in neutral and double-tapping the trigger, you can effortlessly change modes. It is equipped with the M12MC REDLITHIUMMC HIGH OUTPUTMC XC5.0 and CP2.0 battery pack which provides 25% more power, runs 25% cooler, and is chemical resistant to protect against exposure to common oils, greases, and solvents.

• Lighter and more compact
• Very high nut-busting torque – Up to 550 ft-lbs
• 50% faster application speeds
• Mode 1: 0 – 930 RPM Mode 2: 0 – 2100 RPM Mode 3: 0 – 3000 RPM Mode 4: 0 – 1300 RPM
• Triple LED lighting provides high-precision illumination to increase visibility and cast fewer shadows
• Four-mode DRIVE CONTROLMC provides better control over speed and power output. Includes Auto Shut-Off and Bolt Removal modes
• Auto Shut-Off mode prevents overtightening and increases productivity with a maximum torque of 15 ft-lbs.
• New battery pack isolation system for a secure battery pack connection and less vibration transmitted to it
• Compatible with all M12MC battery packs and chargers
• Friction ring system for socket retention Reduces downtime for applications with frequent accessory changes
• One-handed mode change for increased productivity
• Mode 1: 0 – 1500 impacts/minute Mode 2: 0 – 3000 impacts/minute Mode 3: 0 – 3300 impacts/minute Mode 4: 0 – 3300 impacts/minute

• Height 182.9 mm 
• Width 61 mm 
• Length 121.9 mm 
• Weight 997.9 g 

• FUEL™ Yes
• Brushless Motor Yes
• Includes Charger Yes
• Variable Speed Yes
• Motor Type POWERSTATE™ Brushless
• Chuck Size (in) Not Applicable
• Chuck Type Not Applicable
• ONE-KEY™ Enabled No
• Battery System M12™
• Product Type Impact Wrench
• Power Tool Branding FUEL™
• Badge Branding FUEL™
• Anvil Type Friction Ring
• Wrench Type Compact
• Batteries Included / Bare Tool Battery Included
• Maximum Torque (in-lbs) 6600
• Maximum Torque (ft-lbs) 550
• Nut-Busting Torque (ft-lbs) 550
• Battery Amp Hour (Ah) 5
• DRIVE CONTROL™ 4-Mode w/ Auto Shut-Off Mode & Bolt Removal Mode
• Fastening Torque 400
• Maximum RPM 3000
• Anvil Size 3/8 po
• Weight Excluding Battery (lb) 2.2
• Battery Voltage 12
• Blows Per Minute Range (BPM) 0-3300
• Impacts Per Minute Range (IPM) 0-3300
• Rotations Per Minute Range (RPM) 0-3000